Reasons Why Your Nissan Qashqai Key Fob Won’t Work

The Qashqai’s large dimensions give it an SUV-like ambiance. Its ride on 19-inch alloy wheels on Ti and STL versions can also be a bit firm. The front tyres of the Qashqai can lose grip on rough surfaces and its CVT may occasionally exhibit wrist-flexing torque steer.

This is typically caused by an unresponsive coin battery that can be replaced in just a few minutes. Make sure the battery you replace is of the same voltage, size and specification.

Water Damage

One of the most frequent reasons why a Nissan key fob might display the “key ID is not correct” message is due to water damage. The key fob comes with rubber seals that shield the electronic chip inside, but long-term exposure to moisture can cause it not to function properly. This is usually the case when you drop your key fob in the ocean or into a swimming water pool, but it could be the case if it gets wet due to soapy hands or rain.

If your key fob has been exposed to water for the course of a long time then you might need to clean it with isopropyl or electronic cleaner. It could also require to be sent to a professional to repair or replace it.

If your key fob does require replacement, the procedure is relatively easy. Make sure you have the right multipack (CR2032, 3V). Then, open the back and front cases using the small flathead screwdriver. You’ll need to remove the retaining clips made of metal and push out the old battery and replace it with the new one. Reassemble the fob and replace the mechanical key. Verify that it is working correctly. If it does not then you’ll have to take it to your local Nissan dealer or an expert auto locksmith to replace the key chip. The chip isn’t usually damaged by water and isn’t too costly.

Dead Coin Battery

The coin battery is a second common reason why your Nissan Qashqai remote key fob might not function. They typically last for 3 to 5 years, but they can become depleted with time, particularly if the fob is dropped frequently. You can replace the battery, but be sure to use the same voltage and same size as the previous. If you replace the battery, it may cause the key to be assigned a wrong key ID. This will prevent it from being paired with your vehicle.

The most effective method to replace the battery of a coin on the Nissan Qashqai key fob is by prying open the key fob using a small flat head screwdriver. Push in the screwdriver in an angled notch on the bottom of the fob, and turn it around gently to separate the two parts of the key fob. Remove the old CR2025 battery and replace it with a new one, observing the position of the old one in the fob.

Check the terminals for dirt or water damage prior to installing the new battery. If there is, wash the terminals using a small amount of isopropyl alcohol. Make sure that the pole cables are properly connected. They must be connected to the positive and negative poles of your battery.

Diagnostics of a fault

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water, it may be an indication of an internal chip issue. You’ll require a new keyfob if you are unable to fix the issue by replacing the battery. If you dropped the key fob on the ground and it stopped functioning immediately it’s most likely due to damage to the internal chip. It is possible to get the key fob back to work once again if it is removed and [Redirect-Java] clean the chip using paper towel and isopropyl alcohol before putting it back in.

One common error you will see on your dashboard is “Key ID Not Correct.” This means that the vehicle is unable to recognize the key fob and will not allow it to start the engine. The problem can be caused by a variety of things such as water damage, undetectable problems in the circuitry of the key fob or RFID interference.

The key fob won’t work if the 12 volt batteries are dead or fail to provide enough electrical current. This could affect the Nissan Qashqai’s keyless system, central locking and the ability to start the engine with the key fob. If you can’t unlock or lock the door manually it is recommended to check the batteries in your key fob to make sure they’re in good shape. Try installing the battery again to reset your transmitter.

Reprogramming

If the key fob was not submerged into saltwater the device should be able to return to life with a simple wash of clean water. You may also try cleaning the electronic chip with isopropyl alcohol or an electronic cleaner. If these don’t work, it may be time to replace the entire key fob with a brand new one.

If your nissan qashqai key replacement Intelligent Key still does not work, there might be a problem connecting between it and your vehicle. Start by turning the ignition switch without beginning the car. Continue this process until the hazard light blinks twice. After that, turn the car off and remove the keys.

Next, you must open the fob compartment inside your vehicle. This is usually located in a door jamb, on the handle of the driver’s side or under an armrest. Find the small button marked “program” and press it. When the process is complete, you should hear an audible sound.

Now that your Intelligent Key is relinked to the car It’s time to test it out. Make sure you press all the buttons on the key while standing a distance from the vehicle. If the lights flash and the horn squeaks it means that the key has successfully linked to the Nissan. You can also test it near the Nissan.